Lubricating oil stains are one of the stubborn side effects of every cyclist and moped rider. Even the smallest contact with the chain can leave unsightly stains on the skin or textiles that are not so easy to remove. Fortunately, there are suitable home remedies that you can use to counteract and eliminate the smudges.
When you want to remove stains caused by lubricating oil, water is not enough. You need agents that act effectively against the dirt and thus make the cleaning process much easier. Since lubricating oil stains are not easy to remove, the appropriate means are used. If you do not want to buy a special cleaner for lubricating oil stains, usually known as industrial cleaners, there are various home remedies that have a good effect on the stains. In most cases, you already have these at home and can start removing the goo right away. You can find out how to do this in this article.
Before you use any of the home remedies for lubricating oil stains listed below, you should prepare for use. Soiling from lubricating oil begins to dry after a short time and can then be removed mechanically to a certain extent. You can use a butter knife or something similar to gently scrape off the top layer. You should be particularly careful with spots on your skin so that you do not injure yourself. The dirty tool can be cleaned with washing-up liquid. Then a home remedy is used.
Note: If you are dealing with stains on sensitive surfaces or clothing, you should consider a special cleaner. With this, the lubricating oil stains can be removed without negative consequences.
You can always check our website for more content: blog
miracle cure butter
The classic home remedies for stains caused by lubricating oil include butter and comparable fats. If you don’t have butter at home, you can use margarine or another vegetable oil. Butter removes lubricating oil well because it will dislodge from surfaces, fibers, or skin when it comes in contact with them. The advantage: In addition to the butter, you only need a cloth and some washing-up liquid to remove the grease:
- Rub the stain with butter
- for textiles from both sides
- let it take effect for a short time
- dab with a cloth
- if necessary, repeat these steps
- Wash off stains and oil residues with water and washing-up liquid
The use of butter on textiles is particularly suitable, as you can treat them on both sides. If the textiles are dirty, you should put them in the washing machine again afterwards to make the stain disappear for good. Due to the high fat content, stains can also be easily removed from the skin with butter.
Tip: Baby oil has a similar effect on lubricating oil when it comes to fresh stains on bare skin. First rub the area with baby oil and then use water to effectively remove the stains that have not yet dried.
If the lubricating oil stains are on your skin or on metal, glass or plastic surfaces, the use of dish soap is a good idea. This has fat-dissolving properties and can therefore be used excellently against lubricating oil stains, regardless of whether they have already dried or not. With textiles, the use of detergent is not always sufficient, but this depends heavily on whether the stain has already dried. Fortunately, the application is easy to implement:
- Mix water and a few drops of washing-up liquid
- Rub the mixture in well with a cloth
- don’t rub
- Exposure time of the solution: 30 minutes
Be sure to exercise caution with fabrics when using this method. The reason: If lubricating oil stains are rubbed, the smear gets more and more into the fabric and is difficult to remove. Delicate fabrics can be completely ruined as a result. In this case, just dab the stains. Clothing or similar is then washed in the washing machine, while skin and surfaces should be cleaned again with soap to completely remove the grease.
Detergent has a similar effect on lubricating oil stains as dish soap and is actually applied in the same way. Instead of a dish soap solution, make a paste of powdered detergent and water that you can apply to the stain.
The paste should not be applied to your skin, but only to textiles and surfaces. Once you have made the paste, you need to apply it to the stains. After an exposure time of about 45 minutes, the washing machine follows for textiles, while surfaces are cleaned again with a cleaning agent.
Dishwasher tabs: Remove stubborn grease
If the lubricating oil stains have already dried completely and cannot even be removed with the methods already mentioned, you have to bring up other artillery. In this case, it is about tabs for the dishwasher. Due to their composition, tabs efficiently help to get rid of smears as long as the product is not applied to the skin. They would just be too strong for that. On the other hand, you can easily remove smears when they can be seen on different surfaces and textiles. For this you need:
- 1 dishwasher tab
- 1 bucket
- optional: cleaning gloves for sensitive skin
Once you’ve got all the supplies together, you can start cleaning up the goo. With the following instructions, this will be child’s play:
- Step 1: Start by dissolving the dishwasher tab in a full bucket of water. Make sure that the tab is completely dissolved to optimize the effect.
- Step 2: If it is a piece of clothing or fabric, place it in the bucket. On the other hand, if the surfaces are dirty, soak the cloth in the solution until it is soaked. Then place the cloth on the stain.
- 3rd step: The solution should now act for a period of about twelve hours and can then be wiped off or rinsed out with clear water. If shadows remain, they are removed with washing-up liquid.
Remove smear from stones and concrete
If you work with lubricating oil and the product drips onto concrete or stones, don’t despair. There is also a method that you should use for this purpose:
- Step 1: The stains must first be sprinkled with a material that binds the grease. Cat litter or sawdust are very suitable for this purpose. Apply this generously to the stain and wait a moment.
- 2nd step: Now soak the stain, including the binding material, with benzine. The benzine ensures that the stains can be removed in the first place.
- 3rd step: Finally, remove the binding agent and clean with a mild detergent.
Important: Do not use this method on surfaces and floors that are very delicate. An example of this would be parquet floors.